Minwax PolyShades

Minwax PolyShades enhances wood grain by combining beautiful rich stain color and long-lasting polyurethane protection in one easy step.

Wood Stain and Finish, Minwax, Hartnagel Building Supply, Angeles MIllwork & Lumber, Port Angeles, Sequim, Home Depot, Thomas PolyShades can also be used over polyurethane finishes, so you can change the color of your finished wood, without removing the existing finish.  To learn how PolyShades can help you easily change the color of your stained or polyurethane finished wood, view the PolyShades® Color Transformation Guide.

For a complte list of available colors click HERE.

Product Details

Sheens: satin and gloss
Application Tool: high-quality natural bristle brush
Location: interior wood surfaces
Recoat: after 6 hours
Dry Time: 6 hours
Cleanup: mineral spirits
Coverage: 120-150 sq. ft. per quart
Coats: 2 coats are recommended. To deepen the color, apply a third coat.
Recommended Uses: furniture, woodwork, doors, cabinets, accessories

Directions

INTERIOR USE ONLY

WARNING! Removal of old paint by sanding, scraping or other means may generate dust or fumes that contain lead. Exposure to lead dust or fumes may cause brain damage or other adverse health effects, especially in children or pregnant women. Controlling exposure to lead or other hazardous substances requires the use of proper protective equipment such as a properly fitted respirator (NIOSH approved) and proper containment and cleanup. For more information, call the National Lead Information Center at 1-800-424-LEAD (in US) or contact your local health authority.

Surface Preparation:

NOT FOR USE ON FLOORS

For Stripped, Unstained or Raw Wood:

  1. Before starting, surface must be dry, clean and free of dirt, grease and glue.
  2. Sand the wood in the direction of the grain using fine-grade sandpaper (#220) until smooth.
  3. Remove all sanding dust.
  4. To help ensure uniform acceptance of stain color and beautiful results, pre-treat new or raw wood with oil-based Minwax Pre-Stain Wood Conditioner, following label directions.

For Previously Stained Wood That Is Not Being Stripped:

  1. Before starting, surface must be dry, clean and free of dirt, grease and glue.
  2. Lightly sand the wood to ensure adhesion. Remove all sanding dust.

Product Preparation and Color Testing:

  1. Stir Minwax PolyShades thoroughly before and occasionally during use. Do not thin.
  2. Always test stain on a scrap piece or hidden area of wood to verify desired color.

Application:

  1. Using a natural bristle brush, dip approximately an inch into the can, gently tapping it against the inside to remove any excess. Apply a very THIN, even coat following the direction of the grain. Make sure to maintain a “wet” edge.
  2. To minimize the brush marks and bubbles after staining, tip off the surface by holding the brush at a 45 degree angle and lightly run the bristles over the entire length of the wood.
  3. Let the first coat dry for 6 hours or more. Dry time may be extended due to high humidity, low temperatures, and inadequate ventilation or if the coat is applied too thick.
  4. Rub the surface lightly with fine steel wool (grade 000 or finer). Remove all dust. Brush on a second thin coat following directions above. To deepen the color, apply a third coat.

NOTE: For additional protection, without adding color, add a coat of Minwax Fast-Drying Polyurethane or Minwax Wipe-On Poly. Please refer to the back label of the container for application instructions.

COVERAGE: Approximately 120-150 square feet per quart.

CLEANUP: Use mineral spirits following manufacturer’s safety recommendations.

DANGER: Rags, steel wool, other waste soaked with this product, and sanding residue may spontaneously catch fire if improperly discarded. Immediately place rags, steel wool, other waste soaked with this product, and sanding residue in a sealed, water-filled, metal container. Dispose of in accordance with local fire regulations.

CAUTIONS: CONTAINS ALIPHATIC HYDROCARBONS.

Contents are COMBUSTIBLE. Keep away from heat and open flame.

VAPOR HARMFUL. Use only with adequate ventilation. To avoid overexposure, open windows and doors or use other means to ensure fresh air entry during application and drying. If you experience eye watering, headaches, or dizziness, increase fresh air, or wear respiratory protection (NIOSH approved) or leave the area. Avoid contact with eyes and skin. Wash hands after using. Keep container closed when not in use. Do not transfer contents to other containers for storage.

FIRST AID: In case of eye contact, flush thoroughly with large amounts of water for 15 minutes and get medical attention. For skin contact, wash thoroughly with soap and water. In case of respiratory difficulty, provide fresh air and call physician. If swallowed, call Poison Control Center, hospital emergency room, or physician immediately.

DELAYED EFFECTS FROM LONG TERM OVEREXPOSURE. Contains solvents which can cause permanent brain and nervous system damage. Intentional misuse by deliberately concentrating and inhaling the contents can be harmful or fatal.

WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

DO NOT TAKE INTERNALLY. KEEP OUT OF THE REACH OF CHILDREN.

CONFORMS TO ASTM D-4236. Contact a physician for more health information.